ELCO/EDAC

The New Gear: Maintenance, Repair, and Modification Forum.
----Hosted by Al Benoit

ELCO/EDAC

Postby Alain Benoit » Fri Nov 10, 2006 7:24 pm

On this thread I will be posting a pictorial of ELCO/EDAC multipin connector assembly. Specifically a 90 pin female with fixed nut. I have been using multipin connectors extensively for a number of years now and recently I have been leaning towards ELCO/EDAC because of their flexibility of application, ease of use, sound electrical properties and price.
Last edited by Alain Benoit on Sun Nov 12, 2006 12:30 am, edited 2 times in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 7:33 pm

First step is to select the appropriate cable. The following application is for inside a preamplifier rack so a suitable STP (shielded twisted pair) cable will do.
I use exclusively AVP 5110-x cable for many reasons which I will go into on another topic perhaps.

Image
Last edited by Alain Benoit on Thu Feb 15, 2007 8:34 pm, edited 2 times in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 7:37 pm

Next the outer jacket is removed.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 7:40 pm

Then the insulation is stripped from the two conductors.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 7:42 pm

And the two inner conductors along with the drain wire are tinned.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 7:45 pm

The next step involves soldering the ELCO/EDAC pins to the wires.
Here is a closeup of the pin.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 7:57 pm

What makes the ELCO/EDAC connector an excellent choice for audio applications is their bifurcated pin design. Once mated these plated corrosion resistant pins create a low resistance positive electrical contact which is free from intermittance and virtually noiseless.

Image
Last edited by Alain Benoit on Sat Nov 11, 2006 2:23 am, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 8:00 pm

First I prepare the pins by laying them out on double sided Post-It tape.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 8:02 pm

I then solder a pin on each wire.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 8:04 pm

Note the section of 1/16th " clear heatshrink tubing over the drain wire. This is to avoid ground loops and more importantly, in mic level applications, these could be carrying 48VDC which you do not want shorting to anywhere!

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Fri Nov 10, 2006 8:05 pm

Next I slip a piece of 1/8" heatshrink tubing over each of the two signal carrying pins. This is to prevent any cross conducting. I use tubing of two different colours to make identification easier when time comes to insert the pins into the connector body.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 12:26 pm

Here is a front view of the first twelve channels loaded.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 12:29 pm

And here is a rear view. Notice the 3/16" clear heatshrink tubing over each cable and onto the individual wires? This is to prevent any "migrating" of the wires.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 12:30 pm

Here is a shot before the 3/16" tubing got shrunk on the last twelve lines.

Image
Last edited by Alain Benoit on Sun Nov 12, 2006 12:34 am, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 3:23 pm

Here is the finished assembly.

Image
Last edited by Alain Benoit on Sun Nov 12, 2006 12:35 am, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 3:30 pm

Now I've attached a 2ELCO90 for theMiddle Atlantic Products UCP custom rack panel system. I used cap screws and threaded them into the plastic of the connector body from the rear as to not interfere with the mating of the female cable end connector.

Image
Last edited by Alain Benoit on Sun Nov 12, 2006 12:35 am, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 3:33 pm

Here is what the UCP panel looks like installed. Although it is not the specific one which will be housing this particular multipin connector. Notice the fourth panel over from the left is an 1ELCO90 housing a male panel mount which has a female cable mount mated to it.

Image
Last edited by Alain Benoit on Sun Nov 12, 2006 12:36 am, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 11:38 pm

Here is an unloaded female ELCO/EDAC connector with fixed nut, typically used as a chassis mounted connector.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 11:41 pm

Here is a female ELCO/EDAC 90 pin used as a cable mounted connector with actuating screw to assist in mating.

Image
Last edited by Alain Benoit on Sat Nov 11, 2006 11:44 pm, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 11:42 pm

Here is the same connector with the backshell installed.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 11:49 pm

Here is a closeup of an ELCO/EDAC female 56 pin connector with actuating screw and backshell. This particular one is wired to the Alesis ADAT convention.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sat Nov 11, 2006 11:49 pm

Here is a picture of the whole patch. You will notice that it has 8 ins and 8 outs.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sun Nov 12, 2006 12:11 am

Here is some miscellaneous patch using various ELCO/EDAC connector configurations.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sun Nov 12, 2006 12:14 am

The particular wiring convention that I use for my 90 pin connectors follow the AMEK standard. These connectors are used extensively on their large frame consoles. The following picture should explain why, it is a shot of the underside of my onboard patchbay.

Image
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Postby Alain Benoit » Sun Nov 12, 2006 12:17 am

The next picture that I have attached shows an error in wiring. If you look closely the shield and cold pins are reversed.

Image
Last edited by Alain Benoit on Sun Nov 12, 2006 12:38 am, edited 1 time in total.
www.fluidaudiogroup.com

"No one has time to do it right, but we all seem to have time to do it twice."
User avatar
Alain Benoit
Self Biased Resistor
 
Posts: 1321
Joined: Mon Jul 03, 2006 12:21 pm
Location: Canada

Next

Return to Fluid Wireworks

Who is online

Users browsing this forum: No registered users and 21 guests

cron